Skip to main content

WiFI connection 

 
 
root@kali:~# iw dev
root@kali:~# ip link set wlan0 up
root@kali:~# iw wlan0 scan
root@kali:~# wpa_passphrase blackMOREOps >> /etc/wpa_supplicant.conf
root@kali:~# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf
root@kali:~# iw wlan0 link
root@kali:~# dhclient wlan0
root@kali:~# ping 8.8.8.8
(Where wlan0 is wifi adapter and blackMOREOps is SSID)
(Add Routing manually)
root@kali:~# ip route add default via 10.0.0.138 dev wlan0
 
 

Comments

Post a Comment

Popular posts from this blog

SystemD commands

[root@centos7 ~]# systemctl -t target UNIT                   LOAD   ACTIVE SUB    DESCRIPTION basic.target           loaded active active Basic System cryptsetup.target      loaded active active Encrypted Volumes getty.target           loaded active active Login Prompts graphical.target       loaded active active Graphical Interface local-fs-pre.target    loaded active active Local File Systems (Pre) local-fs.target        loaded active active Local File Systems multi-user.target      loaded active active Multi-User System network-online.target  loaded active active Network is Online network.target         loaded active active Network nfs-client.target      loaded active active NFS client services nss-user-lookup.target loaded active active User and Gr...
Post a Comment
Read more

How to tweak linux server harddisk using hdparm

hdparm switches explained http://manpages.ubuntu.com/manpages/intrepid/man8/hdparm.8.html   First of all you have to install hdparm in linux. apt-get install hdparm #hdparm /dev/sda /dev/sda: readonly = 0 (off) readahead = 120 (on) geometry = 8850/255/63, sectors = 142182912, start = 0 Hard disk Performance Information # hdparm -tT /dev/hda /dev/hdd: Timing cached reads: 496 MB in 2.00 seconds = 247.42 MB/sec Timing buffered disk reads: 60 MB in 3.03 seconds = 19.81 MB/sec Hard drive set to low, slow settings # hdparm -cuda /dev/hda /dev/hda: IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) readahead = 256 (on) Use below tweaks to increase disk read write performance. For sda drive ~]# hdparm -a 2048 /dev/sda /dev/sda: setting fs readahead to 2048 readahead = 2048 (on) For sdb drive [root@439298a ~]# hdparm -a 2048 /dev/sdb /dev/sdb: setting fs readahead to 2048 readahead = 2048 (on) ]# echo “anticipatory” >...
Post a Comment
Read more

RAID

Check the Raid installed lspci | grep RAID     Software Raid ============== Linux Support For Software RAID Currently, Linux supports the following RAID levels (quoting from the man page): LINEAR RAID0 (striping) RAID1 (mirroring) RAID4 RAID5 RAID6 RAID10 MULTIPATH, and FAULTY. MULTIPATH is not a Software RAID mechanism, but does involve multiple devices: each device is a path to one common physical storage device. FAULTY is also not true RAID, and it only involves one device. It provides a layer over a true device that can be used to inject faults. Install mdadm Type the following command under RHEL / CentOS / Fedora Linux: # yum install mdadm Type the following command under Debian / Ubuntu Linux: # apt-get update && apt-get install mdadm How Do I Create RAID1 Using mdadm? Type the following command to create RAID1 using /dev/sdc1 and /dev/sdd1 (20GB size each). First run fdisk on /dev/sdc and /dev/sdd with " Softwa...
Post a Comment
Read more